BKK Fangs-62 UA Treble Hooks #8 (8pcs)

Product detailed description

BKK Fangs-62 UA #8 is the first size below the working saltwater crossover #6 that SAF positions purely for spinning. It is particularly well suited to smaller hardbaits, crankbaits and compact jerkbaits measuring approximately 4.5–6.5 cm, spoons and small casting jigs. Its purpose is to combine low rigging weight with the strength reserve of forged 2X wire. Size #8 is therefore not presented primarily as a pilker hook; its own role is light freshwater spinning and finely balanced replacement rigging for smaller hardbaits.

Lure length alone does not determine the correct hook size. The treble must retain free movement, exposed points and the original balance of the lure. A slim 6 cm minnow may need a smaller hook than a shorter but wider crankbait. Body width, number and spacing of hook hangers, split-ring size, buoyancy and the weight of the original rigging all matter. The 4.5–6.5 cm range is therefore a practical starting point, not a universal conversion.

The 2X designation describes the wire and strength class, not an exact load rating in kilograms. Fangs-62 is neither an extra-fine 1X treble nor a heavy-duty model for extreme fishing. With a small lure, confirm that the 2X construction preserves its action; at the same time, the additional mechanical reserve can be a practical advantage over a finer original hook.

The geometry is based on a traditional O’Shaughnessy bend. BKK combines it with a forged shank, regular eye and three needle-sharp points with standard barbs. According to the manufacturer, forging increases strength by approximately 20% compared with similar non-forged hooks. The reliability of the complete rig also depends on split-ring condition, point sharpness, drag setting and the angle at which the fish takes the lure.

The hook is manufactured from BKK-81WV high-carbon steel and finished with an Ultra-Antirust (UA) coating for increased corrosion resistance in saltwater. It can therefore be used in both freshwater and saltwater. After saltwater fishing, rinse the hook with fresh water, allow it to dry completely and inspect the points, eye, split ring and any mechanical damage to the coating.

On hardbaits, minnows and crankbaits measuring approximately 4.5–6.5 cm, size #8 makes sense when #10 or #12 do not provide enough working gape. On a lure fitted with two trebles, confirm that the front and rear hooks do not lock together during casting or twitching. Check the buoyancy of a floating lure, the neutral position of a suspending model and, on a crankbait, whether the larger hook profile adds enough resistance to change the frequency or stability of its action.

On smaller spoons and casting jigs, #8 is useful when the points need more clearance beyond the sides of the lure but #6 would add unnecessary weight to the rear rigging. With a spoon, compare its rocking action during a slow retrieve and its flutter on the fall. With a casting jig, confirm that the hook does not repeatedly catch the line or the lure body during the cast, sink or retrieve.

Size #8 is practical for lighter spinning for perch, trout, chub, asp and smaller zander, always according to the specific lure and complete tackle setup. This is not a load rating or a maximum fish-size statement. Line or braid diameter, leader strength, drag setting, rod action and the way the fish is played remain equally important.

Among the neighbouring sizes, #10 is the finer choice for minnows and crankbaits measuring approximately 4–5.5 cm. #8 adds working gape for common smaller hardbaits around 4.5–6.5 cm and light metal lures. #6 is the larger crossover size that SAF still uses for pilkers and speed jigs up to 6 cm / around 20 g.

The UA coating also allows size #8 to be used in saltwater, but its primary decision-making role at SAF is spinning. When rigging a small saltwater hardbait or coastal minnow, rinse the hook with fresh water after fishing, allow it to dry completely and inspect all three points after every contact with rock or another hard obstruction.

Fangs-62 UA #8 is not automatically a substitute for every treble hook carrying the same size number. Hook sizing is not dimensionally standardised between manufacturers, and ranges also differ in wire diameter, shank length, bend geometry and weight. If you need significantly lighter rigging, compare a 1X model. If heavy-duty resistance is the priority, consider an appropriate 3X or 4X range after physically checking its proportions.

The BKK Fangs-62 UA size table is an approximate guide to the complete range. It is not a universal conversion between lure length and hook size. Before final rigging, always check the physical proportions of the specific lure, the original hook, split-ring size, freedom of movement and the lure’s behaviour in the water.

This version contains 8 treble hooks in size #8. According to the reference chart, one hook weighs approximately 0.45 g. Before first use, check the sharpness of all three points and repeat the inspection after every contact with rock or another hard obstruction. Replace a blunt or mechanically damaged point; an intact-looking coating alone does not prove that the hook remains sharp.

BKK Fangs-62 UA #8 is suitable for anglers looking for a lightweight 2X replacement treble hook for smaller hardbaits and crankbaits. Its main role begins with lures measuring approximately 4.5–6.5 cm, where #10 may not provide enough gape while #6 could unnecessarily alter the balance or action of the lure.

Frequently asked questions – BKK Fangs-62 UA #8

Which lures suit size #8?

It is a suitable starting point for hardbaits, minnows, crankbaits and smaller jerkbaits measuring approximately 4.5–6.5 cm, spoons and small casting jigs. Always check the physical proportions and action of the specific lure.

Is size #8 suitable for hardbaits measuring 4.5–6.5 cm?

Yes, this is a practical starting range for many smaller hardbaits. Body width, number of hooks, buoyancy and the dimensions of the original rigging can still shift the correct size.

What is the difference between sizes #10, #8 and #6?

#10 is the finer choice for lures around 4–5.5 cm. #8 offers more working gape for hardbaits around 4.5–6.5 cm. #6 is the larger crossover size with a role on small saltwater metal lures.

Will size #8 change the buoyancy or action of a hardbait?

It can. According to the reference chart, one hook weighs approximately 0.45 g. Test floating, suspending and sinking lures in the water and compare the new rigging with the original hooks.

Can size #8 be used on a spoon or casting jig?

Yes, provided it has enough clearance around the body without overloading the lure. Check the rocking action and fall of a spoon and the freedom of movement of a casting jig.

Can BKK Fangs-62 UA #8 be used in saltwater?

Yes. Ultra-Antirust increases corrosion resistance. After fishing, rinse the hook with fresh water, allow it to dry completely and inspect both the points and the coating.

Is size #8 a direct replacement for every original #8 treble hook?

No. Hook numbering is not dimensionally standardised between manufacturers. Compare overall height, gape, weight, wire, eye and the real action of the lure rather than relying on the size number alone.

→ Full technical details are listed below in the Product Parameters table.

↓ Related and similar products are also shown below the description to help you choose the right components and build a complete setup.