Powder Paint Fluid Bed XL

Product detailed description

The XL powder paint fluid bed is a larger container for finishing pilkers, cheburashka weights, jig heads and lead sinkers. Match working clearance and the air source to the actual casting and chosen powder.

Compared with smaller plastic cup-style fluid beds, the Powder Paint Fluid Bed XL feels much more stable. The body is made of steel with a surface finish, has more weight and sits firmly on the workbench during use. This is important when handling hot lead, larger castings or a stronger airflow. The cylinder does not behave like a lightweight plastic cup that tends to move around the table or tip over easily.

Inside the fluid bed, the paint is lifted by air and starts to behave like a fine fluid layer. The heated lead casting is dipped briefly into this fluidised paint, allowing the coating to bond more evenly to the surface than with ordinary cup dipping. The result is cleaner, more consistent and easier to repeat, especially on castings with edges, rounded transitions, eyes, ribs or more complex shapes.

The XL version is suitable for larger and more demanding castings. Compared with smaller fluid beds, it offers more space, a larger paint volume and better comfort when dipping longer or wider pieces. This is useful especially for sea fishing pilkers, larger cheburashka weights, end weights, heavier jig heads and castings that are harder to coat accurately in a small fluid bed.

The fluid bed has a diameter of 90 mm and a height of 240 mm. The usable working height for coating is approximately 200 mm, so longer lead castings can be guided into the cylinder more comfortably. Depending on the type of coating material, casting size and working method, the cylinder is suitable for approximately 200–400 g of paint.

An XL extension adapter can also be added to this fluid bed, increasing the working height even further. This is especially important when coating longer sea fishing pilkers, elongated weights and larger castings where you need more space above the paint layer. With the extension adapter, the Powder Paint Fluid Bed XL becomes a more serious workshop setup for regular work with sea fishing pilkers and longer lead lures.

The Powder Paint Fluid Bed XL is supplied with a base frame, hoses and regulating valves. The regulating valves allow you to fine-tune the airflow so the paint is lifted evenly inside the cylinder without being blown out. Correct airflow adjustment is essential – too little air will not lift the paint properly, while too much air can throw the paint around and reduce control during coating.

For a good result, work with a clean casting, correct lead temperature and stable airflow. If the casting is too cold, the paint will not bond properly. If it is too hot, the layer can become too thick or uneven. A short and controlled dip into properly fluidised paint usually works better than a long dip.

Dimensions and fill: 90 mm diameter, 240 mm overall height and approximately 200 mm usable working height. A typical fill is 200–400 g, depending on the coating and casting. The setup includes its base frame, airlines and control valves. The Powder Paint Fluid Bed Extension Cup for XL adds space for longer pieces.

XL with the Hailea compressor is the main recommended setup for rubberized coatings. It also works with the XL extension, providing room for longer pilkers and a larger fill. For powder paint in XL, use APS 400 or the Hailea ACO-208 Compressor for Rubber Coating. APS 400 is suitable here for powder paint only, not rubberized coating. Connect both bed inlets: directly to APS 400’s two outlets, or through suitable air distribution and regulation from Hailea’s single outlet.

A larger bed does not guarantee that every powder will fluidise. Check the coating type, moisture, fill quantity and airflow on a small test batch. Preheating and curing temperatures depend on the particular coating.

An even finish depends on clean metal, its temperature and steady airflow. A cold casting may not pick up the powder correctly, while an overheated one can produce an excessively thick coat. Test one piece and adjust the setup before coating a whole batch.

Frequently asked questions (FAQ)

Which setup is best for rubberized coatings?

The XL fluid bed with the Hailea compressor, optionally with the XL extension. APS 100 and APS 400 are not suitable for rubberized coatings.

Can XL also be used for powder paint?

Yes. For powder paint, use APS 400 or Hailea. Connect both inlets and regulate airflow to the powder fill.

Are XL and Amigo extensions interchangeable?

No. The XL extension fits the XL bed; the Amigo extension fits onto the Amigo plastic cup.

Is 240 mm the working depth?

No. Overall height is 240 mm and practical usable height about 200 mm. A typical fill is 200–400 g, depending on powder and castings.

→ Explore further equipment in the Fluid beds category.

↓ Compare related accessories and alternative products below to match your coating setup.